Replacing Lock on uPVC Door
If you're looking to change the lock on your door made of upvc it is necessary to remove the existing handle and screw holes. This is usually easy to accomplish.
Then, locate the screw that holds in the lock barrel. This screw is typically a different color than the other screws, and is situated on the outside of the faceplate of the lock.
Take the Cylinder off
The first step to change the lock on your upvc door is to take off the current lock cylinder from the door. This is a relatively simple process that can be done in about 30 minutes. All you require is an screwdriver. The Euro cylinder screw is usually located on the inside edge of the door, right next to the lock cylinder. The screw is typically different in color from the other screws and should be easy to spot. Remove this screw and keep it in a safe location.
Once the cylinder is removed, you can begin working on removing the handle. To do this, you will have to open the door wide enough so that you can observe the inside edge of the door as well as the faceplate on the outside of the lock.
Remove the screw that binds the handle to the door by using a screwdriver. Once the screw is removed you should be able to pull the handle toward you and the rest of the mechanism out of the door.
If you are having trouble getting the handle off the door frame, you might have to unscrew it. This can be accomplished using a drill or screwdriver, and you'll need to be careful not to damage the screw head or cross-thread the screw.
When you are ready to replace your cylinder, ensure that it is the correct size for the door you have. Cylinders are measured according to two measurement points: (a) the distance from the centre of the Fixing Screw hole to the bottom of the cylinder and (b) the distance between the keyhole and the edge of the lock plate.
Take the handle off
The good news is, when your upvc handle gets stiff, floppy or loose, it is an easy solve. The cause is usually down to wear and tear with the cylinder or internal parts of the multipoint lock which are located inside the door between the handle and the handle frame. Weather conditions, heavy use or ageing can cause upvc locks wear. This can cause problems with the closing and locking mechanisms of the door.
If the cylinder is been damaged, it can be difficult to turn the key and the lock can also become stiff, which could cause the handle to loosen. This can be fixed by replacing the cylinder, which is an easy procedure. This can be done by yourself, however you will require some knowledge about the mechanism's operation. The first step is to remove the handle, which will allow you to get access to the valve and replace it with a brand new one.
You'll need an electric screwdriver and measuring tape for this. It is essential to know the exact measurements of the cylinder you have in place so that you can order a replacement cylinder that is suitable for. The cylinder allows you to lock the door of your upvc. upvc window lock repair cost is essential that you order an upgrade that is the same size.
To take off the old cylinder, it is need to take off the screws which hold it in place. Be careful not to remove the screws, as this could make it very difficult to remove them in the future. Once the screws are removed the cylinder will slide out easily.
Remove the Lock Barrel
Upvc is a very durable material that is designed to ensure that you and your family are secure. They are available in various designs and colors to match any style. They are also energy efficient and maintenance-free. They are not without disadvantages. Over time, the barrel or locking point lock can become faulty and need to replaced. It is a simple procedure, but you should be aware of a few things prior to beginning.
To get to the screw that holds the lock cylinder, you will need to remove your door handle. This screw is usually different in color from other screws and can be located near the keyhole on the outside of your door. Take out this screw and put it in a safe location. Slide the handles out on both the inside and outside of the door. Be sure to take your time and not move too fast, as it may harm your uPVC door.
After removing the handles, you can use a screwdriver to take out the screws that secure the handles to the door frame. This will allow you to gain access to the support pins that are holding the cylinder in place. After that, you can try wiggling and tugging the device to see if the cylinder comes loose. When it is loose then pull it back towards you, and then pull it out of the socket.
Once you have removed the old cylinder lock, it is important to replace it with a brand new one with anti-snap and anti-bump protection. You can do this yourself if have the right tools, or you can engage an expert locksmith to do it for you. This is a simple task that shouldn't take more than five minutes.
Install the New Cylinder
A door lock made of upvc can be damaged or broken in a variety of ways, for example, a tenant may have moved out and not returned the key, or the cylinder may be damaged and is no longer functioning as it should. It is important to choose the right size replacement for your upvc door lock. If the wrong one is installed, your doors may be more susceptible to the 'lock snapping technique that is responsible for 25% of burglaries.
It is important to install the proper cylinder. The process is easy and takes less than five minutes. You will need a screwdriver to take off the screws that attach to the faceplate on the handle and the cylinder, but once you have done this it's a simple job to swap them over.
Before you get started, make sure that the handle is in a position to open and that you have complete access to the inside edging of the door as well as the handle's faceplate which holds the lock cylinder. This will let you easily remove the lock cylinder from the handle without the need to move it, and expose the internal parts of the frame.
The next step is to take the old cylinder out and measure it. You must be aware of the overall length as well as the diameter of the cam that rotates to lock and unlock the door. This will enable you to locate a new cylinder that's the same or smaller. This is the most crucial part of the entire process. A cylinder must be flush with the backplate of your handle and be no more than 5mm away from it.
Install the Handle
It is not uncommon for a door lock made of upvc to stop working and this could be caused by something breaking inside the case which controls the bolts that retract into the keep or strike plate. This can often be solved by adjusting the Allan key under the hinges. However, this could cause stress on the parts within the central casing, and it is advised to seek out a professional.
It is crucial to have quick and easy access to both sides when changing the handle. It is essential to use the correct tools. It is also a good idea to prop the door open to ensure it doesn't close during the procedure.
First, loosen the screws holding the handle in place using the screwdriver. Once they are loose the handle can be removed. After the cylinder and handle are removed, it's now time to install the new handle. Make sure the new handle is compatible with your existing central cylinder and cylinder. To determine the correct size, measure the spindle length on the lever that you currently own. Also ensure that the screw fix centres on the handle are the same as the screw fixing centres on your current cylinder and hole centre.
Replacement handles from Fab & Fixed are available in various styles and are built to last. They are perfect for those who want to upgrade their upvc handles and improve their home security. The right handle will ensure that your home is secure and safe and won't be easy for burglars to break into.